Reverse Cycle Air Conditioner Guide for Melbourne Homes
A Melbourne buyer’s guide to choosing a reverse-cycle system, sizing it for your home and comparing running costs.
All Electric HomesIf you’re replacing gas heating, start with the rooms you’re trying to keep warm. A split system might be all you need for an open-plan living area. If you want warm bedrooms with the doors shut as well, the job needs a different design. Get that right before comparing brands or chasing the biggest kW number.
How does a reverse cycle air conditioner work?
A reverse cycle air conditioner is a heat pump for your home. In winter, it takes heat from the outdoor air and moves it inside. In summer, it reverses the process and moves heat out. Because it moves heat rather than generating it directly, it can deliver several units of heat for every unit of electricity it uses. The ratio changes with the model, outdoor temperature and how the system is running. Solar Victoria’s guide to reverse cycle
Which type suits your home?
| System | Where it makes sense | What to check |
|---|---|---|
| Single split | A bedroom, home office or main living area. You can add separate units later if you want to upgrade in stages. | Where the indoor head and outdoor unit will go, and which rooms the air can actually reach. |
| Multi-split | Several rooms need their own indoor heads, but space for outdoor units is limited. | How much heating capacity the shared outdoor unit can deliver when several rooms are calling for heat at once. |
| Ducted reverse cycle | Several rooms need heating and cooling, and you’d prefer vents instead of wall-mounted heads. | Space for ducts and return air, which zones can run independently, and whether any existing ducts are suitable. Don’t assume old gas ducts can be reused. |
What size reverse cycle air conditioner do you need?
For a single room or one open area, Solar Victoria gives these rough starting points:
- Up to 20 m²: around 2–2.5 kW.
- 20–40 m²: around 2.5–5 kW.
- 40–60 m²: around 4–6 kW.
These figures describe system output, not electricity drawn from the wall. They’re a starting point for a quote, not a sizing rule. A draughty front room with high ceilings and single glazing can need more heat than a well-insulated room of the same size. For ducted or multi-room installs, ask for a room-by-room assessment rather than sizing from total floor area. Solar Victoria’s sizing guide
When comparing units, look for the cold-climate heating figures on the Zoned Energy Rating Label where available. Melbourne is in the cold zone for this label. Compare the estimated heating electricity use of units with similar output, and ask what heating capacity the proposed model can deliver on a cold morning. For a ducted model without a label, ask for the manufacturer’s published performance data. How to read the Zoned Energy Rating Label
Is reverse cycle cheaper to run than gas?
It can be, but compare the cost of delivering the same amount of heat to the same rooms. Here’s what that looks like with example rates, not a quote or a Melbourne-wide savings estimate:
| To deliver 1,000 kWh of useful heat | Example assumptions | Energy cost |
|---|---|---|
| Reverse cycle | Delivers 3 units of heat per unit of electricity; electricity at 30¢/kWh | $100 |
| Gas heating | Delivers 80% of the gas energy as useful heat; gas at 3.5¢/MJ | About $158 |
Use the rates on your own bills. How much of the house you heat, the condition of the old system and how often you use cooling will change the result. The example excludes daily supply charges. If you still use gas for hot water or cooking, don’t count the gas supply charge as a saving. If heating is your last gas appliance, check the cost of closing the account or abolishing the connection before including that saving.
What should you ask the installer?
- Why this size? Ask for the exact model, its heating and cooling output, and which rooms it’s designed to cover.
- What’s included in the price? Check the electrical circuit, any switchboard work, pipe or duct runs, drainage, equipment removal and who handles gas decommissioning if required.
- Where will the outdoor unit go? Check noise near bedrooms or neighbours, service access and where water from the outdoor unit will drain. If you’re in an apartment, check with your owners corporation before committing to a location.
- Who does the work and what will I get at handover? Check the relevant refrigeration, plumbing and electrical credentials. Ask for the applicable compliance paperwork, including the Certificate of Electrical Safety for electrical installation work, plus the equipment and workmanship warranties.
- Is the Victorian Energy Upgrades discount included? Ask for the amount to be shown separately and confirmed for your replacement. Check eligibility before buying the unit or starting work.
Energy Safe Victoria: working with tradespeople · Victorian heating and cooling discounts
Planning a switch from gas? Start with the free All Electric Homes upgrade calculator for an indicative estimate. Our in-house refrigeration mechanics and electricians coordinate the sizing, switchboard checks and installation through one team. The site visit confirms the installation scope, so you can see what needs doing now and what can wait before you commit.